DIY Tub Installation.
DIY Tub Installation.
Blog Article
Have you been hunting for additional info concerning Installing A Bathtub?
Installing a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and often, tiling skills. Replacing an old tub with a brand-new one is also a moderately challenging task. If the old bathtub is readily obtainable, the project can move immediately; if you need to open a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the brand-new one. Make certain you have qualified yourself for the task and also fit trying it. As opposed to hiring a contractor to take over a halfway-completed job, it is much better to think about using one prior to you start. Opportunities are you may require a professional plumber to make tube connections.
This short article will help you install a new bath tub in your bathroom if you have actually currently purchased a brand-new tub as well as don't require to transform the setup of your previous water supply pipes.
Your tools and product list must make up the following:
Planning for the Installation
Firstly, the supporting structure provided with the bath should be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the limited access that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipes. When the supply pipelines have actually been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old securing substance.
Prior to going on to fit the new faucets, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Making use of both wooden boards under its feet, put the tub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the level and also changing the feet on the bath tub till the spirit level reviews degree.
To install faucets, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipe by making a compression join; then do the very same for the various other faucet.
Activate the water system as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the tub and also examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Lastly, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been made use of a minimum of once as this will resolve it right into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in location between the tap and also the sink. Safeguard the tap in place with the manufacturer provided backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind needs to be connected to the faucet finishes initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, creating the water to permeate the wall between the bath and also the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealer can break rather very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that review about A Step-by-Step Guide to Installing a Bathtub while doing a search on the search engines. Those who enjoyed reading our page plz don't forget to pass it around. Thank-you for going through it.
Set An Appointment Report this page